lexaiden@lexserv01 ~: sudo badblocks -vsw -t 0xAA -t 0x55 -b 4096 -c 2048 /dev/sdl [sudo] Passwort für lexaiden: Es wird nach defekten Blöcken gesucht (Lesen+Schreiben-Modus) Von Block 0 bis 976754645 Es wird getestet Mit Muster 0xaa: erledigt ) Lesen und Vergleichen:erledigt ) Es wird getestet Mit Muster 0x55: erledigt ) Lesen und Vergleichen:erledigt ) Durchgang beendet, 0 defekte Blöcke gefunden. (0/0/0 Fehler) lexaiden@lexserv01 ~: sudo smartctl -AiH --log=error /dev/sdl [sudo] Passwort für lexaiden: smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.14.3-1-MANJARO] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 5K4000 Device Model: Hitachi HDS5C4040ALE630 Serial Number: PL2310LAG0L47C LU WWN Device Id: 5 000cca 22ec04415 Firmware Version: MPAOA250 User Capacity: 4.000.787.030.016 bytes [4,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Dec 15 12:39:17 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 98 3 Spin_Up_Time 0x0007 100 100 024 Pre-fail Always - 512 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 9 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 115 115 020 Pre-fail Offline - 41 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 169 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 7 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 10 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 10 194 Temperature_Celsius 0x0002 181 181 000 Old_age Always - 33 (Min/Max 21/38) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 1 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 78 f0 93 5e 00 Error: ICRC, ABRT 120 sectors at LBA = 0x005e93f0 = 6198256 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 80 e8 93 5e 40 00 00:00:19.336 WRITE DMA EXT 25 00 80 68 93 5e 40 00 00:00:19.335 READ DMA EXT 35 00 80 68 93 5e 40 00 00:00:19.334 WRITE DMA EXT 25 00 80 e8 92 5e 40 00 00:00:19.334 READ DMA EXT 35 00 80 e8 92 5e 40 00 00:00:19.333 WRITE DMA EXT